The top bars are double fully welded and super strong, No telescopic top inserting legs to scratch and slide in and out whilst trying to install like all other brands with there tops and drilling and bolting up. This is truly as custom factory tower that will still adjust to suit your boat using our Indy IP2 tower system we developed. The system allows for a rock solid tower for towing you friends and family. No other tower uses this easy to install factory tower.The best deck mounts on the market makes install on the top or angle side of you boats deck a breeze, No need for exact alignment like all other brands to allow for folding, our mounts will rotate under pressure to allow the tower to pivot and lower flat. Check out the video of folding the tower in less than 60 sec by one person for storage. We take the extra time and effort to make sure the best quality material used in the production of the tower, using 6063 seamless, thick 3mm walled tubing, 6061 solid fittings and 316 stainless steel bolts and washers. They are then handcrafted and bent to perfection and hand welded after which the highly skilled polishers, polish the tubes and fittings to the highest finish. We then go one step further than other brands, the highly polished towers are then dipped and clear anodized coating of the towers and fittings for that superior finish to protect you investment for many years to come. This has the added bonus of a easy to clean tower with no polishing need and no grubby finger marks. So you can be assured your investment is not some cheap, poor quality product that will be destroyed in the marine environment. The finer details are the difference. No complicated fitting or alignment. DIY 2 - 4 hours to fit. 1 person to lower for storage. Fits boat 17 - 25ft long. Front 67 inches to 102 inches wide mounting.
Rear 70 inches to 102 inches wide mounting. 55 inches tow point from mounting position. 2.25 inch 6063 Aircraft seamless Aluminium.
CNC 6061 Aircraft Aluminium fittings. 316 Marine grade Stainless M12 bolts and washers.Anodized coating or Glossy powder coated Black. Best deck mounts on the market. Solid fully weld double bar top section. Our Pro Bimini will fit this tower above or below top.
Of our bimini top, is the rotating end fittings on the adjustable beam. When you attach to a Liquid or Liquid pro tower across the front legs, it allows you to detach the rear support arms and pivot the bimini for lowering it down with your Liquid or Liquid Pro tower. No need to completely remove from the tower. For extra safety whilst out on the water with family and friends you can attach our.
Attaching around the front bar of the bimini it is easy to adjust for different drivers to see behind them, checking the rider, passengers and rear approaching boats. You can fit this universal indy wakeboard tower bimini top to other wakeboard towers. Materials We use only genuine marine grade VIII, UV resistant material for the covers as we want our products to last in the marine environment. We use strong stiff 304 stainless steel for our frames and steel hardware. You do need to maintain the frame with regular polishing and cleaning.
The mounting clamps are alloy 6061 Aircraft CNC machined with rubber inserts to product your tower. How to check the bimini is correct size for your wakeboard tower. Mark the height you want the tower bimini to sit at on your wakeboard tower at the front and also rear legs. Now measure across the boat from side to side between the front legs. Write down this measurement and repeat the process for the rear legs.Keep in mind the bimini must go through the smallest measurement. Size of the Pro wakeboard tower bimini top. Large 1580V model - 62 in (W) x 75 in (L) or 1.6m (W) x 1.9m (L). Small 1350V model - 53 in (W) x 75 in (L) or 1.35m (W) x 1.9m (L). Size of clamps 2.5inch clamps with 2.25inch rubber inserts.
If you have different size smaller tube say 2 inch let us know upon ordering. Over the top wakeboard tower bimini. This will allow you to mount the tower above your tower point by attaching the clamps and T raisers to your towers top bar point them upwards and attach to the solid adjustable cross beam. Have the support arms facing down so they can attach to the front legs of you tower. This is easy to set up on our Liquid towers as seen in the pics.
The wakeboard tower bimini will also fit like this on a number of other aftermarket brands, such as Origin, Reborn, Monster, Aerial, BigAir waketowers, Krypt etc. This item is in the category "Sporting Goods\Water Sports\Wakeboarding & Waterskiing\Other Wakeboarding/Waterskiing". The seller is "originwakeboard" and is located in this country: US. This item can be shipped to United States, Canada.